OpelScanner
OpelScanner => OpelScannerCAN => Topic started by: Artur on November 28, 2018, 23:26:04
-
Dear users of our second generation interface,
The new update (ver. 2.0.1.66) is available for download.
This is a bit special update. On the first connection it will update the firmware in the interface.
It will last 2-3 seconds, then you just need to replug the interface and continue to use it as before.
After update you will be able to connect to the interface also via BlueTooth. Selection of the connection type is on the Settings page.
The BlueTooth board currently is not installed in the interface. You can buy then online and configure by yourself, or order from us.
All instructions will be published later.
From now on if you want to work via USB - make sure you connect our adapter to the USB cable, and only then to the vehicle.
Otherwise BlueTooth connection mode will be activated and won't be detected via USB.
_____________________________________________
Уважаемые пользователи нашего интерфейса второго поколения,
Новое обновление (версия 2.0.1.66) доступно для загрузки.
Это специальное обновление. При первом подключении программа обновит прошивку в интерфейсе.
Перепрошивка будет длиться 2-3 секунды, после вам просто нужно будет переподключить адапетр и продолжить использовать его по-прежнему.
После обновления вы сможете подключиться к интерфейсу также через BlueTooth. Выбор типа подключения есть в настройках программы.
В настоящее время плата BlueTooth не установлена в интерфейсе. Вы можете купить ее онлайн и настроить самостоятельно, или заказать у нас.
Все инструкции будут опубликованы позже.
С этого момента, если вы хотите работать через USB - убедитесь, что сначала наш адаптер подключен к компьютеру USB-кабелем, и только затем подключайте к автомобилю.
В противном случае будет активирован режим подключения BlueTooth и по USB адаптер не будет определяться.
-
Принимайте новенького).
Я владею опель астра j 2.0CDTI 2013 г.
Хочу активировать БК на дополнительную информацию.
Как я могу купить ваш интерфейс?
-
Если по России, обращайетсь в ECUtools.ru
-
Я не в России. Есть способ международной покупки?
-
Напишите на info@opel-scanner.com
-
Dear users of our second generation interface,
The new update (ver. 2.0.1.66) is available for download.
This is a bit special update. On the first connection it will update the firmware in the interface.
It will last 2-3 seconds, then you just need to replug the interface and continue to use it as before.
After update you will be able to connect to the interface also via BlueTooth. Selection of the connection type is on the Settings page.
The BlueTooth board currently is not installed in the interface. You can buy then online and configure by yourself, or order from us.
All instructions will be published later.
From now on if you want to work via USB - make sure you connect our adapter to the USB cable, and only then to the vehicle.
Otherwise BlueTooth connection mode will be activated and won't be detected via USB.
I need help. On USB, no problem. On bluetooth, COM6 selected and connected, red led inside interface slow blink. I select an Z18XE ecu, I click Start, red led goes steady red, but no information appears on screen.
What do I do wrong?
-
Did you install BT module in it? It needs to be programmed to 115200 kbs.
-
I did install it. I managed to arrange the bluetooth, was something wrong on my side with the drivers.
Now it connects ok, it start searching for the ECU, but it returns an error that it cannot find it. The yellow/red buttons top right of the app blink until error comes.
No, I haven't program anything to 115200 kbs yet, its a bit too late tonight, but I will have a look tomorrow evening.
Thanks so far.
-
Fine, please share here your experience. Thanks!
-
Did you install BT module in it? It needs to be programmed to 115200 kbs.
When you say to be programmed to 115200 kbs, do you refer to the BT module itself? If yes, how is the programming done? Was it supposed to be done by the dealer?
If you refer to my laptop bluetooth interface, I can't find any possibility to change com port speed ....
-
Yes, module must be programmed to 115200. It can be done with any USB-TTL programmer. DOnt touch laptop BT.
-
Ok, challenge accepted. But installation is not user friendly, it should of not been sent to me as final user, unless configured? And if not configured, I should of been told so?
Just sayin..
-
If you purchased interface with BT board inside, then it should work.
-
Hello, sorry, but we dont have version in Spanish.
As for help - only outdated version is available.
-
Hello, sorry, but we dont have version in Spanish.
As for help - only outdated version is available.
WHAT IS THE VERSION IN WHICH THE HELP WORKS BECAUSE IT DID NOT WORK WITH THE INSTALLATION VERSION OF THE PURCHASE CD
-
Please write on info@opel-scanner.com, we will help you.
-
Hello, sorry, but we dont have version in Spanish.
As for help - only outdated version is available.
I bought the bluetooth card from one of your dealers.
-
con questo aggiornamento si connette alla mia nuova vettura opel crossland x 1200 130cv?
ciao
-
Soon.
-
Hi. Where i can buy this interface?
-
On our site - www.opel-scanner.com
-
Connect casually with like-minded individuals on the ultimate dating platform.
Living Women
Top-notch casual Dating (https://datesnow.life)